Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Spring Repair for Yonkers Homeowners
A broken spring turns your garage door into a dead weight of several hundred pounds, and it usually happens without warning, often with a loud bang from inside the garage. We repair and replace torsion and extension springs for homeowners across Yonkers, and we treat it as the safety-critical job it is. Our technicians have up to 10 years of experience, and we work on whatever brand is already on your door, from Wayne Dalton to Craftsman to Raynor. Same-day service is available for spring failures, and you can reach us at (877) 492-2580. Every job starts with a written price you approve before any work begins.
What Our Garage Door Spring Repair Service Includes
Springs are the counterweight system that makes a heavy door feel light. There are two families of spring in residential doors, torsion and extension, and each fails in its own way. Here is what each part of our spring work covers.
Torsion Spring Replacement
A torsion spring is the coiled steel mounted on a shaft above the door, and it stores the tension that lifts the door. It’s under extreme load at all times, which is why a torsion spring failure is loud and sudden. We replace the spring, wind it to the correct number of turns for your door’s weight, and balance the door so the opener isn’t fighting it. On most doors the two springs are a matched pair, and when one breaks the other has usually lived the same life, so we’ll tell you plainly what we recommend and why.
Extension Spring Replacement
Extension springs run along the horizontal tracks on either side of the door and stretch rather than twist. They’re common on older doors and on many Wayne Dalton and Craftsman setups, and they need safety cables running through them so a broken spring can’t fly loose. We replace extension springs in pairs, fit fresh safety cables at the same time, and check that the door closes evenly with no gap on one side. If your door has been sluggish or slams down hard, an extension spring that has lost its stretch is often the reason.
Broken Spring Repair
A snapped spring is the most common call we get, and it usually means the door won’t open at all or opens a few inches and stops. Don’t keep running the opener against it, because the motor will strain and the door can come down hard. We confirm which spring failed, check the cables and drums for damage the break may have caused, and replace what’s needed in one visit. Spring repair is a dedicated service for us, not a side job between other work, because this is the most mechanically dangerous part of any door.
Spring Adjustment
Sometimes the spring isn’t broken, just out of tune, and the door feels heavy, drifts down on its own, or reverses before it reaches the floor. Adjustment means setting the tension so the door balances at mid-height and the opener only has to guide it. We measure the door’s balance and travel, adjust the springs to match, then test the safety reverse. A door that’s properly balanced puts far less strain on the opener and closes more quietly.
Safety Cable Installation
Safety cables are the steel runs threaded through extension springs so that when one breaks, the pieces stay contained instead of swinging across the garage. Many older doors were built without them, and it’s one of the simplest upgrades we make on a spring visit. We fit cables rated for the load, anchor them at both ends, and check the track and brackets while we’re there. It’s a small addition to a spring job that makes the whole system safer.
Spring Inspection
A spring inspection looks for the warning signs that don’t announce themselves: a gap in the coil, rust pitting, a stretched extension spring, or cables starting to fray at the drum. We check the springs, cables, drums, hinges and rollers together, because a problem in one usually shows up in another. You get a clear picture of what’s fine now, what’s wearing, and what needs attention soon, with a written estimate for anything we recommend. We can put together a plan for a repair from Yonkers Garage Door Repair Pros.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Spring Repair
We work on whatever brand you have, and that matters most with springs, because the right spring has to match your door’s weight and track, not just a label. LiftMaster and Craftsman systems are common on Yonkers doors, and we know how their openers interact with a torsion setup: how the travel limits behave when a spring goes slack, and why the opener’s force settings need resetting after a spring replacement. We diagnose the whole system, not just the part that broke.
Wayne Dalton and Raynor doors show up often too, and each has its quirks. Wayne Dalton extension setups and their TorqueMaster-style torsion tubes call for specific spring sizes, and Raynor doors are built around their own track and spring geometry, so a generic replacement won’t sit right. Whether you have one of those or any other make, we can help. We service LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor equipment, and the technician who diagnoses your spring is the same one who finishes the job. There’s no handoff to another contractor.
Signs You Need Garage Door Spring Repair Right Now
- A loud bang from the garage. A torsion spring breaking sounds like a firecracker or a heavy book hitting the floor, and it usually means the door won’t lift. If you heard it and the door stopped working, stop using the opener and call us.
- The door feels extremely heavy. If you can barely lift the door by hand, the spring has lost its tension or snapped. Forcing it is how people get hurt, so leave it down until a technician checks it.
- A visible gap in the spring coil. A clean break in the coil is easy to see once you know to look. Don’t reach up to touch it; a broken spring can still hold stored energy.
- The door opens a little and stops. When the opener lifts the door partway and gives up, the spring isn’t carrying the weight and the motor is doing all the work. Keep running it and you risk burning out the opener too.
- The door drifts down or closes unevenly. A door that won’t stay up at mid-height, or closes with a gap on one side, points to a spring out of balance. It’s a sign to get it adjusted before something fails.
Our Garage Door Spring Repair Process – Step by Step
- 1
We ask what happened first. Before we touch anything, we want to know whether you heard a bang, whether the door moved, and whether the opener is still working. That tells us a lot about which spring failed and whether the cables took any damage.
- 2
We inspect and test the whole system. A technician measures the door’s weight and balance, checks the springs, cables, drums and rollers, and looks at how the opener is set up. Springs don’t fail in isolation, and a break often leaves marks on the cable or drum.
- 3
We give you a written, upfront price. You get the price before any work starts, including the springs and anything else that needs replacing. If we find a cable or drum the broken spring damaged, it’s in the estimate, not added afterward.
- 4
We replace the spring safely and set the tension. We use the correct winding bars and the right spring for your door’s weight, replace matched springs as a pair where that’s what the door needs, and fit safety cables on extension setups. The door is then balanced and the travel and force settings on the opener reset.
- 5
We test the door and walk you through it. We run the door through full open and close cycles, check the safety reverse, and show you what we replaced and what to watch for. You’ll know the door is working the way it should before we leave.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Spring Repair Cost in Yonkers?
Spring repair in Yonkers typically runs $180 – $340 for a single spring, and that’s the estimate most homeowners are working from. Because springs are usually replaced as a matched pair, a pair costs about twice that range. The price depends on whether you have torsion or extension springs, the door’s size and weight, and whether the broken spring damaged a cable or drum. High-lift and heavy doors take more spring, and a door on a Wayne Dalton TorqueMaster tube is different work from a standard torsion setup, so both affect the figure. A cable repair runs $130 – $250, and general garage door repair is $150 – $600, if the spring break knocked something else out of line.
The way to avoid overpaying is simple: get the written estimate before work starts, and make sure it covers the springs and any related parts in one number. Our free estimate includes the inspection, a look at the cables and drums, and a clear price. The written estimate sets the final price, and that’s what you pay. If you want a second look at an old door that keeps costing you, we can also talk through garage door spring repair options and whether a replacement door makes more sense than another round of repairs.
Garage Door Spring Repair Near Yonkers – Our Service Area
We cover Yonkers and the towns around it, including Ardsley, Piermont, Elmsford, Orangeburg, South Nyack, Valhalla, West Nyack, Thornwood, Bardonia, Hillcrest and New City. Same-day service is available for spring failures, and an urgent call goes to the front of the schedule. Wherever you are in the area, the process is the same: a written estimate, the right spring for your door, and a balanced door before we leave. For the northern towns, a technician covering garage door spring repair can usually reach you the same day.
Serving Yonkers, NY – Our Local Coverage Area
We serve Yonkers and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Spring Repair in Yonkers
Garage door spring repair is the work of replacing or adjusting the springs that counterbalance your door’s weight so the opener doesn’t have to lift the whole thing alone. It covers torsion springs on the shaft above the door and extension springs along the tracks, plus the safety cables that keep a broken spring contained. Because the springs are under extreme tension, the work is done with proper winding tools and the door tested for balance afterward. This is the most dangerous part of any garage door, so we don’t recommend homeowners attempt it. Call (877) 492-2580 for a free estimate.
Most spring replacements take about an hour to two hours once the technician is on site. That covers the inspection, the spring replacement, resetting tension, and testing the door and opener. If a broken spring damaged a cable or drum, it can take a little longer because those parts are replaced in the same visit. We confirm the timeframe when we give you the estimate. Call (877) 492-2580 to book a visit.
Spring repair in Yonkers typically costs $180 – $340 for one spring, and a matched pair costs about twice that because both springs are replaced together. The final price depends on whether your door has torsion or extension springs, its size and weight, and whether anything else was damaged. The written estimate sets the final price, and it’s quoted before work begins. Call (877) 492-2580 for an exact quote, and estimates are free.
Yes. We service Wayne Dalton equipment, including their extension spring and TorqueMaster torsion setups, and we know where those systems wear out. Wayne Dalton doors are built around specific spring sizes and track geometry, so a generic replacement won’t balance the door correctly. We match the spring to your door rather than the other way around. Call (877) 492-2580 and tell us the model, and we’ll take it from there.
Yes. Emergency garage door service is a core part of what we do, for doors stuck open, doors that won’t close, and broken springs that leave your home exposed or unsafe. We’ll get you scheduled as quickly as we can, with same-day service available for spring failures. When a spring has snapped, call before you try the opener again. Reach us at (877) 492-2580.
We stand behind our work and check every repair by running the door through full open and close cycles and testing the safety reverse before we leave. The warranty terms are explained in writing with your estimate so you know what’s covered on the springs and labor. We’d rather you ask up front than wonder later. Call (877) 492-2580 if you have questions about coverage.
Leave the garage clear enough for the technician to reach both sides of the door, and move anything parked under the door or blocking the tracks. Don’t try to lift the door or touch the springs, and if the door is stuck open, keep people and pets away from the opening until we arrive. If you can, have your door’s brand and any known model details handy. Then call (877) 492-2580 to book the visit.
Schedule Your Garage Door Spring Repair Service in Yonkers Today
A broken spring doesn’t fix itself, and every day you leave it, the opener and cables take more strain. Call Yonkers Garage Door Repair Pros at (877) 492-2580 for same-day availability, a free estimate, and a written price before any work starts. Our technicians have up to 10 years of experience, and we work on whatever brand you have. If your door is stuck open or the spring has snapped, call now and we’ll get you scheduled. Emergency service is available, and an estimate is free. We also handle garage door spring repair for homeowners across the river.
Written by the team at Yonkers Garage Door Repair Pros.